Luckily they survived and a few days later I tried them out with the paintstiks. They’d dried out and so were a little fragile but luckily they were quite thick and leathery to start with. I placed the leaves under some muslin and then rubbed with several different coloured paintstiks including gold, using my finger to blend the colours.

I left these to set for a day, and then because the background fabric was uninteresting I decided to back each leaf with fusible web, cut them out individually then applied them to a piece of black batik fabric. I used a free motion zigzag and variegated rayon thread to stitch round the edge of each leaf, and then I stitched along the outline of each leaf vein. I felt that the leaves needed something else such as metallic thread so that was on my shopping list when I went to the quilt show in England, and  yesterday I added the last bit of stitching.

Now I need to find a good fabric for the border and quilt the design.

I imported the photo into EQ6 and then because of the complexity of the design I decided I would draw out the pattern in two parts, first concentrating on the hornbill and then creating another layout focusing on the background palm fronds. I did this and then once the background was drawn I copied and pasted the hornbill into the background.

To create the wall hanging I started off with some fabric that I had hand painted for the sky and invisible machine appliqué to construct the design. Normally I use freezer paper templates which I iron to the wrong side of the fabric and then remove after the construction is completed but for this design as there were so many small pieces I didn’t want to have to cut the back to remove the paper. I used a different method where I still use freezer paper templates but iron the paper to the front side of the fabric and then turn the edges under to wrong side using the tip of an iron and spray starch painted onto the seam allowance. The spray starch helps to hold the seam allowance in place.

I printed out the full size pattern from EQ6 and then traced the outlines onto a stabilizer which I pinned in place under my ’sky’ fabric. The fabric was light enough for me to be able to see the lines through so that I could place my pieces accurately.

I used a lot of fine pins to hold the appliqué pieces in place for stitching. I used invisible thread with a fine thread in the bobbin and a very fine needle (#60/8) and started stitching the pieces in place a few at a time as I built up the design on the background.

I had a lovely striped batik fabric which proved to be just perfect for creating the varied colouring of the palm fronds.

The fronds at the lower edge of the picture were so small and had such sharp points that I decided to fuse them in and use raw edge appliqué. To quilt I used invisible thread and outlined all the fronds and the bird, with stippling in the background areas and meander quilting with variegated cotton thread in the borders.

The finished design.

To protect my work surface I covered everything with an old shower curtain, as the paint gets everywhere and is difficult to remove. I mix my paints in foil dishes and use a plant mister to dampen the fabric before painting. My favourite book on fabric painting is Mickey Lawler’s Skydyes and I used her directions for painting my sky by blending  ultramarine and cobalt blues to create a more realistic effect. In one dish I blended ultramarine with a dash of cobalt and in the other cobalt with a dash of ultramarine. I misted the fabric quite liberally and then used a  brush to apply the paint in broad stripes.

This picture shows the wet fabric and you can see quite clearly where I have applied the two different blues. As you can see from the next photo the fabric dries much paler.

The next day I moved on to sun printing and creating a ’sea’ fabric.  For the sea I again followed Mickey Lawler’s directions although this time I also I added a layer of opaque pearlescent white to the dampened fabric which gives the finished piece a lovely sparkle. For the painting I used various mixes of emerald, ultramarine and cobalt.

I sprinkled the wet fabric with course salt and purposely scrunched it up with a few creases going across the width, then laid it out to dry in the bright sun.

I was pleased with the way this turned out, the ridges have created lines which have the appearance of rolling waves and the salt gives the effect of sea spray.

The hornbill in the photo below is one that I have just completed using my last batch of painted fabric.

I used some of the leftover ’sea’ fabric to try sun printing and again following Mickey’s advice I chose some delicate leaves to make the prints. She says that soft leaves work better because they lie flat against the surface of the fabric, so actually for this I hunted around the garden and grabbed some creepers that were growing wild near one of the garden walls.

The wet fabric and leaves out in the sun, and below the sun printed fabric.

My final experiment was to add some ‘jungle’ to one of my pieces of sky fabric. This time I used a sponge to apply the paint. I only wetted the lower edge of the fabric where I wanted the colours to run into each other, and I used a little less water with the paints. I aslo used salt again and dried the fabric in the sun but on a tilt which gave an interesting effect with the salt.

I created this intending to use it just as a background for a new hornbill design that I’m going to do, but I was so pleased with the way that it turned out that I now want to design a new wall hanging around it. I already have an idea so I will write about it soon.