How to add a single fold binding to your quilt

IMG_0907

People often want a reminder on how to sew on their binding once they finish their quilt or wall hanging so I have put together this tutorial for my blog. It also contains instructions for adding a sleeve if you are going to hang your finished quilt.

These instructions are for adding a single fold binding to your quilt or wall hanging using a ⅜” seam and with the finished width of ⅜” for the binding.

First measure the outside edges of your quilt or wall hanging to determine how many strips you will need to cut from your binding fabric. For example, if your quilt measures 20” x 16” you will need a total of 72” of binding plus a bit extra to go round the corners and for joining, so if your fabric is 45” wide you would need to cut 2 strips.

Cut your required number of strips from the width of the fabric 1¾ inches wide. Using your ruler and rotary cutter, cut the ends of each strip at a 45˚ angle, the join right sides together as shown to form one continuous strip using a ¼” seam. I find it helps to mark the ¼” seam on your binding strips. Strips joined using a 45˚ angle like this are stronger and almost invisible when viewed from the right side.

joining the binding strips

joining the binding strips

After stitching trim off the little ends of fabric that stick out.

joined binding strips

Strips joined with a 45˚ seam and the ends trimmed off.

It’s important that you have trimmed all the edges and squared up the corners before you attach your binding.

Lay the binding right side down onto the front (right side) of your quilt, stitch round all the edges with a ⅜ inch seam. Start your stitching 4-5 inches away from the end of the binding and leave that end loose, its good to start about mid way down one of the sides of the quilt.

To miter the corners, when you get close to the corner stop stitching and make a mark ⅜“ away from the edge. Continue stitching until you reach this mark and then stitch diagonally out to the outer edge.

Stitch from the 3/8" intersection mark diagonally to the outer edge.

Stitch from the 3/8″ intersection mark diagonally to the outer edge.

Cut you thread and then fold the binding up at a 45˚ angle, then fold down so that it is level with the edge of your quilt. Start sewing at the fold and then continue to the next corner and repeat the steps.

Fold the binding strip up on the diagonal

Fold the binding strip up on the diagonal

Fold down again so that the fold is level with the edge of your quilt and start stitching.

Fold down again so that the fold is level with the edge of your quilt and start sticking.

Stitch until you are about 8-9 inches away from where you first started stitching and stop
Joining the binding.

Lay the quilt flat with the binding on top and then mark with a pin ½” away from the edge of the 45˚ angle.

Put a pin 1/2" from edge of binding

Put a pin 1/2″ from edge of binding

Lay the other end of the binding over the top of the first one and make a mark or insert a second pin where it overlaps the underneath pin. This will be your cutting line for the other end of the binding. Cut this end at 45˚. I find it helps to draw a line on the top binding to show which direction to cut the angle.

Lay the other end of the binding on top and mark

Lay the other end of the binding on top and mark

Lay the second piece on top and mark.
Join the two ends with a ¼” seam, press the seam open, and then stitch the last part of the seam.

Stitch the ends of the binding together using a 1/4" seam.

Stitch the ends of the binding together using a 1/4″ seam.

Hanging sleeve
Next attach the hanging sleeve if you are making a wall hanging.
For the hanging sleeve cut a piece of fabric from the backing fabric the same width as your finished quilt and 9 ½” wide.
Make a seam at each end by turning in ¼” and then ¼” again to the wrong side, press and stitch in place close to the inside edge.
Once the stitching is complete fold in half lengthways and then press lightly to mark the lower edge.
Centre the hanging sleeve on the back of the quilt, having the raw edges even with the top edge of your quilt and then stitch in place using a ⅜” seam. Secure each end by backstitching.
To complete, turn the binding to the back of the quilt, fold in the raw edge and slip stitch in place on the back. Make sure that your stitches are only on the back of the quilt and don’t show through to the front.

Binding turned to the wrong side ready to be hand stitched in place.

Binding turned to the wrong side ready to be hand stitched in place.

Stitch the hanging sleeve in place last.

Stitch the hanging sleeve in place last

Stitch the hanging sleeve in place last. Make a fold and pin level with top of quilt to make extra room so you can insert a rod for hanging.

To make a little extra room in the sleeve so you can insert a hanging rod make a fold in the top of the hanging sleeve tube and align with the top edge of your quilt and pin in place. Now lay the sleeve flat and slip stitch the sides and lower edge in place. Don’t stitch the top edge. When this is unpinned there will be a small fold of loose fabric which will allow for the insertion of a hanging rod.